pcb

Yakiniku Recipe

Posted on Updated on


Bahan

  • 400 gram daging sapi sukiyaki
  • 1 buah bawang bombay, potong-potong
  • 1 buah paprika hijau, potong-potong
  • 2 sendok makan mentega/margarin

Saus pencelup

  • 2 buah bawang putih, parut
  • 1 cm jahe, parut
  • 100 cc kecap kikkoman
  • 50 cc mirin
  • 1/4 sendok teh garam
  • 1 sendok teh gula pasir
  • 1/4 sendok teh merica bubuk
  • 1/4 sendok teh bumbu penyedap

Cara

  • Saus pencelup: campur semua bahan, aduk hingga rata, sisihkan.
  • Campur daging sapi dengan sebagian saus pencelup, diamkan selama 15 menit.
  • Panaskan margarin, lalu masukkan daging sapi tadi, bawang bombay, dan paprika hijau, masak sampai matang sambil sekali-sekali dibalik.
  • Biasanya yakiniku disajikan bersama-sama dengan saus pencelup.

sumber : http://www.dunia-ibu.org/dapur/resep-34/Yakiniku.html

 

Hari sabtu ini akan ada makan-makan PCB Team Samsung lagi, dan rencananya kita akan masak bareng Yakiniku disana. Resepnya sepertinya gampang. cuma ga ada sayurannya disana, jadi sepertinya resepnya akan diubah-ubah sedikit. Semoga menu nya sukses nanti. Kalo temen-temen yang sedang baca punya ide tambahan tolong kasih tau ya, acaranya masih Sabtu ini :p

Iklan

[Solved] Dynamic shape not updating

Posted on Updated on


Question :

Hi,

I have a problem with dynamic shape on my board.

dynamic shapes on the board not updating even they are not voiding from any where. shape fill type is smooth and I try to update it from Display>Status>update dynamic shapes but error msg occured

“1 dynamic shape is still out of date or empty.  Run Out of date shapes Report from status dialog to identify them.”

I also try to DB doctor my pcb but not working. In the starting shape was fine Error occured suddenly I didnt know how it happens.

previously I have this problem and I resolved it by chance by removing internal plane layers from Xsection and again defined them. but I know this is not a proper solution.

Baca entri selengkapnya »

Cara Membuat Keyboard Shortcut di Cadence PCB editor

Posted on Updated on


Buat temen2 yang pasti nya sering make Cadence, biasa ngaktifin tombol add connect pake apa?kalo copy?kalo move?kalo delete..kalo??

kalo biasanya pake mouse, Saya juga udah nyoba sebelumnya dan rasanya cm satu tangan yang gerak, ntar jempol kiri iri karena jempol kanan lebih gede, hehehe

Saya barusan nyoba ngoprek si cadence trus nemu cara buat ngedit keyboard shortcut nya

caranya agak ribet dikit

Baca entri selengkapnya »

HDMI Design Guidelines : Layer Stack-up, Differential Pair

Posted on


This article presents design guidelines for helping users of HDMI mux-repeaters to maximise the device’s full performance through careful printed circuit board (PCB) design. We’ll explain important concepts of some main aspects of high-speed PCB design with recommendations.
This discussion will cover layer stack, differential traces, controlled impedance transmission
lines, discontinuities, routing guidelines, reference planes, vias and decoupling capacitors.

Layer stack

The pin-out of a HDMI mux-repeater is tailored for the design in HDTV receiver circuits (see Picture below). Each side of the package provides a HDMI port, featuring four differential TMDS signal pairs, thus resulting in three input and one output port. The remaining signals comprise the supply rails, Vcc and ground, and lower speed signals such as the I2C interface, Hotplug-detect and the mux-selector pins.


FIG 1. The device pin-out is tailored for HDTV receiver applications

Baca entri selengkapnya »